MOEN - Kitchen Faucets - Kitchen - The Home Depot MOEN - Kitchen Faucets - Kitchen - The Home Depot

Moen faucet hookup, department

Step 3 slip new sprayer hose down through sprayer hole Position the New Sprayer Hose Slip the new sprayer hose down through the sprayer hole, and feed it up through the center faucet hole. Step 4 two wrench technique helps prevent twisting Attach the Flexible Connectors The hot and cold supply tubes on the faucet may vary in length, depending on the brand.

Tighten the nuts by hand, then tighten with a basin wrench. In that case, you may need to wait and attach one of them from underneath the sink once the faucet's in place. Depending on the size of the hole, you may have a tight fit and thus be able to attach only one flexible connector before seating the faucet assembly.

If not, replace it with the one included with the new faucet. The manufacturer's instructions may direct you to set the new faucet assembly in place, then crawl back under the sink to make the new connections. Use an adjustable wrench to connect the hose to the sprayer nipple.

Then feed the connected lines down through the hole in the sink. Step 2 unscrew coupling nuts from supply tubes to faucet use basin wrench to remove mounting nuts lift out old faucet and disconnect sprayer hose Remove the Old Faucet Using a basin wrench, reach up behind the faucet, and unscrew the coupling nuts connecting the supply tubes to the faucet figure 1.

catcountry105.com: Online Shopping for Electronics, Apparel, Computers, Books, DVDs & more

Lift out the sprayer hose. Tighten the connections with an adjustable wrench. Step 6 attach the second flexible connector attach male ends of connectors to shutof valves Tighten the Connections Attach the second flexible connector if you haven't already Image 1and attach the male ends of the connectors to the shutoff valves Image 2.

Use the basin wrench to remove the mounting nuts holding the faucet in place figure 2.

Spider man dating

You may want to attach flexible connectors to adapt the faucet for a particular installation. Save yourself from struggling in cramped quarters by making all the connections you can before setting the new assembly in place. If so, attach them to the fittings on the faucet's supply tubes.

Indianapolis dating

Pro Tip It's time to connect the new faucet's fittings with the water-supply lines. Step 5 seat the faucet once gasket lines up correctly install washer and nut to end bolts of faucet Seat the Faucet Insert and feed the connectors and supply lines into the center hole, and, making sure that the faucet's gasket lines up correctly, seat the faucet Image 1.

Executive dating sites

If the sprayer-hose escutcheon cap is in good shape, you may want to leave it on. Use a small adjustable wrench to disconnect the hot- and cold-water supply lines from the shutoff valves Image 2. With the attachments at the base of the faucet assembly already in place, the only work you'll need to do under the sink is to connect the supply lines to the shutoff valves.

Travel dating blog

From under the sink, install a washer and nut -- or a plastic nut-washer combo Image 2 -- to the end bolts that will hold the faucet in place. Open the faucet to drain Moen faucet hookup excess water. Use two wrenches to tighten each connection -- one to hold the faucet-fitting stationary and one to turn and tighten the female fitting on the flexible connector.

For service and support call

After the faucet is removed, use a scouring pad to clean the sink surface thoroughly. Turn the water on at the shutoff valves, and turn on the faucet to check whether Speed dating beverly ma working properly.

Dating sites for free in kenya

This two-wrench technique will help prevent twisting and damaging the faucet's copper supply lines. With the mounting nuts disconnected, lift out the old faucet, and use an adjustable wrench to disconnect the sprayer hose from the assembly figure 3.